ProCurve 420 Informações Técnicas Página 71
- Página / 363
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Using the HP Web Browser Interface
Status Reporting Features
Web: Viewing Detected Neighbor APs
After AP detection scanning, use the AP List window on the AP Detection tab
to view the table of detected neighbor access points.
Figure 4-17. The AP Detection List Window
The neighbor AP table displays the following information:
■ BSSID: The Basic Service Set Identifier (wireless MAC address) of the
detected access point.
■ SSID: The configured Service Set Identifier. Listed SSIDs that have the
same BSSID indicates multiple SSIDs configured on one access point.
■ Channel: The wireless channel being used.
■ RSSI: The Receive Signal Strength Indicator, which is a measure of the
strength of the signal received from the detected access point. The higher
the value, the stronger the signal. An RSSI value of 30 or more indicates
a strong signal from a nearby access point that may cause significant
interference problems. An RSSI value of 15 or less indicates a weak signal
from a distant access point, which should not impact wireless network
performance.
■ Radio Mode: The operating mode of the access point; 802.11b or 802.11g.
4-27
- HP ProCurve 3
- Wireless Access Point 420 3
- Disclaimer 4
- Warranty 4
- Publication Number 4
- Applicable Products 4
- Trademark Credits 4
- 8 Command Line Reference 9
- A File Transfers 14
- Getting Started 15
- Introduction 16
- Conventions 16
- Command Prompts 17
- Screen Simulations 17
- Related Publications 18
- Sources for More Information 20
- Need Only a Quick Start? 20
- Advantages of Using the CLI 25
- Browser Interface 26
- Accessing the CLI 28
- Telnet Access 29
- Secure Shell Access 29
- Using the CLI 30
- Username: admin 31
- Password: 31
- Command Level Operation 32
- How To Move Between Levels 34
- ? symbol lists the 35
- Command Option Displays 37
- Configuration Modes 38
- CLI Control and Editing 42
- General Features 47
- The Home Page 49
- Support URL 50
- Web Browser Interface Logout 51
- Interface Session 52
- Setting SNMP Community Names 54
- SNMP] button 55
- Setting the Primary SSID 56
- Setting the Radio Channel 57
- Configuring TCP/IP Settings 58
- [Modify] button for the 60
- [Security Suite] button 60
- Status Reporting Features 62
- Station Status 65
- Event Log 67
- The Status Bar 68
- Neighbor AP Detection 68
- Settings] button 69
- 5. Click the 70
- button 70
- Passwords 77
- Figure 5-1. The User Window 79
- Modifying System Information 86
- CLI: Setting the System Name 87
- Configuring IP Settings 89
- Figure 5-5. The SNMP Window 95
- General System Configuration 102
- Configuring SNMP 102
- SNMP Trap] button 103
- Enabling System Logging 114
- [Event Log] button 115
- System Servers] button 115
- [Apply Changes] button 115
- Configuring SNTP 119
- CLI: Setting SNTP Parameters 121
- Parameters 123
- Accounting Servers] button 128
- Setting up Filter Control 132
- Filter Control] button 133
- CLI: Setting Traffic Filters 134
- Configuring VLAN Support 136
- Web: Enabling VLAN Support 137
- CLI: Enabling VLAN Support 139
- Contents 141
- Overview 142
- Setting the Country Code 143
- Port/Radio Settings] button 147
- [Radio Mode Change] button 147
- Configuring Radio Settings 150
- Modifying Antenna Settings 156
- Control Limits 158
- Add] button 163
- Wireless Security Overview 171
- Using the Security Wizard 179
- Configuring RADIUS Client 193
- Authentication 193
- Configuring MAC Address 199
- Command Line Reference 207
- General Commands 210
- HP420#reset board 213
- System Management Commands 215
- Default Setting 217
- 99 (no country set) 217
- HP420(config-mgmt)# 221
- System Logging Commands 234
- HP420(config)#logging clear 238
- HP420(config)# 238
- Example 239
- System Clock Commands 240
- SNMP Commands 245
- Command Mode 259
- Flash/File Commands 260
- HP420#bootfile hp420-2.bin 261
- HP420#delete test.cfg 263
- RADIUS Authentication 267
- HP420(if-wireless-g-ssid-1)# 270
- RADIUS Accounting 273
- 802.1X Authentication 278
- 802.1x session-timeout 280
- 802.1x supplicant user 280
- 802.1x supplicant 281
- MAC Address Authentication 284
- Filtering Commands 288
- Ethernet Interface Commands 292
- HP420(if-ethernet)# 293
- HP420(if-ethernet)#shutdown 296
- Wireless Interface Commands 299
- HP420(if-wireless-g)# 301
- HP420(if-wireless g)# 305
- Wireless Security Commands 321
- IAPP Command 335
- VLAN Commands 336
- File Transfers 341
- [Start Upgrade] button 355
- Index – 1 359
- 2 – Index 360
- Index – 3 361
- *5990-6006* 363
Manuais e produtos relacionados com Software ProCurve 420
Software ProCurve 2610-PWR Informações Técnicas
(469 páginas)
(469 páginas)
Software ProCurve 2610-PWR Informações Técnicas
(364 páginas)
(364 páginas)
Software ProCurve 2510G Series Informações Técnicas
(412 páginas)
(412 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais